2n Helios Ip Vario User Manual

2N® Helios IP Force is a highly resistant and reliable IP door access intercom provided with a lot of useful above-standard functions. Supporting the SIP standard and being compatible with the leading IP PBX and telephone suppliers, 2N® Helios IP Force can make use of all VoIP services. 2N® Helios IP Force can work as a standard. Page 1 ® 2N Helios IP Vario Door Entry IP Intercom Installation Manual Version: www.2n.cz.; Page 2 2N TELEKOMUNIKACE a.s. Administers the FAQ database to help you quickly find information and to answer your questions about 2N products and services.

Use a PC equipped with any web browser to configure 2N® IP Vario:

  • Launch your web browser (Internet Explorer, Firefox, etc.).
  • Enter the IP address of your intercom (http://192.168.1.100/, e.g.).
  • Log in using the Admin user name and 2n password.

You have to know the IP address of your device to log in to the integrated web server. By default, 2N® IP Vario is switched into the dynamic IP address mode, i.e. it obtains the IP address automatically if a properly set DHCP server is available in your LAN. If no such DHCP server is available, you can operate 2N® IP Vario in the static IP address mode.

IP Address Retrieval

If your device remains inaccessible (you have forgotten the IP address, or the LAN configuration has changed, for example), change the LAN settings using the buttons on the device.

Take the following steps to retrieve the 2N® IP Vario IP address:

  • Connect (or, if connected, disconnect and reconnect) 2N® IP Vario to the power supply.
  • Wait for the second sound signal.

    • 1-button models: Press the quick dial button on the basic unit five times.

    • 3-buttons models: Press the second quick dial button on the basic unit five times.

    • 6-buttons models: Press the fifth quick dial button on the basic unit five times.

  • 2N® IP Vario will read its IP address.
  • If the address is 0.0.0.0, it means that the intercom has not obtained the IP address from the DHCP server.

Note

  • Be sure to press the button sequence within thirty seconds after the sound signal for security reasons. Up to 2 s intervals are allowed between the presses.

Static IP Address Setting

2n helios ip vario user manual software

Follow the instructions below to enable the static IP address mode:

2n Helios Ip Vario Manuale

  • Connect 2N® IP Vario to the power supply (or, disconnect and reconnect it if already connected).
  • Wait for the first acoustic signal .
  • Press following buttons sequentially:

    • 1, 1, 1, 2, 2, 3 for 3-buttons models

      Switching to static IP address

    • 4, 4, 4, 5, 5, 6 for 6-buttons models
  • The acoustic signal indicates mode switching.
  • Wait until the device is restarted automatically.

2n Helios Eye

Note

  • The 1, 1, 1, 2, 2, 3 sequence must be entered within 30 seconds after the first sound signal for security reasons. The inter-digit delay may be 2 s at most.

The device will have the following network parameters after restart:

  • IP address – 192.168.1.100
  • Network mask – 255.255.255.0
  • Default gateway – 192.168.1.1

Dynamic IP Address Setting

Connect 2N® IP Vario to the power supply (or, disconnect and reconnect it if already connected).Follow the instructions below to enable automatic getting of network parameters from the DHCP server:

  • Wait for the first acoustic signal
  • Press following buttons sequentially:

    • 2, 1, 1, 2, 2, 3 for 3-buttons models

    • 5, 4, 4, 5, 5, 6 for 6-buttons modely

  • The acoustic signal indicates mode switching.
  • Wait until the device is restarted automatically.

Note

  • The 2, 1, 1, 2, 2, 3 sequence must be entered within 30 seconds after the first sound signal for security reasons. The inter-digit delay may be 2 s at most.

2N® IP Vario gets the IP address upon restart only if the DHCP server is configured properly.

Mode Switching with 1-Button Models

Connect 2N® IP Vario to the power supply (or, disconnect and reconnect it if already connected).In case your 2N® IP Vario device is equipped with 1 button, you can switch the modes using one button only.

  • Wait for the first acoustic signal .
  • Press the quick dial button 15 times.
  • The acoustic signal indicates mode switching.
  • Wait until the device is restarted automatically.

Switching between static and dynamic IP address

2n ip vario factory reset

2n Helios Ip Vario Configuration Manual

Note

2n Helios Ip Vario User Manual Software

  • The 15 times 1 sequence must be entered within 30 seconds after the first sound signal for security reasons. The inter-digit delay may be 2 s at most.

2n Helios Ip Vario User Manual Download

The static IP address mode will be switched into the dynamic IP address mode and vice versa upon restart.